在路面坑槽、車轍、龜網裂銑刨時，不需要設置銑刨過渡段，依據設計的銑刨深度，結合路面確定的病害面積，確定銑刨機基準面和橫坡，靠近病害一側部位進行銑刨，要求銑刨機調整找平儀始終保持正常的工作狀態進行銑刨作業，直該病害區域銑刨完畢。

When milling grooves, ruts, and turtle net cracks on the road surface, there is no need to set up a milling transition section. Based on the designed milling depth and the determined area of the road surface, the benchmark surface and cross slope of the milling machine are determined, and milling is carried out near the diseased side. The milling machine is required to adjust the leveling device to maintain normal working status throughout the milling operation until the diseased area is fully milled.

在病害路面修補大于二個結構層時，應把路面的不同結構層分層錯臺銑刨，且每層小錯臺不小于50cm，以利于面層修補時不同結構層接縫錯開。

When repairing a damaged road surface with more than two structural layers, the different structural layers of the road surface should be milled and planed in layers, and the small misalignment of each layer should not be less than 50cm, in order to facilitate the staggered joints of different structural layers during surface layer repair.

在油包擁包銑刨拉毛過程中一定要控制好三個關鍵環節以確保銑刨拉毛效果，開始銑刨過渡段，銑刨機銑刨深度要從零緩慢調整到計算的銑刨深度；第二，銑刨過程中銑刨深度調整段，無論是增大還是減小銑刨深度，都要從原銑刨深度逐漸調整到新的銑刨深度，嚴禁突變，這就要求在劃定銑刨區間時標定好調整過渡段的位置；第三，結束銑刨過渡段，銑刨機也要將原銑刨深度緩慢降低到零。

In the process of milling and roughening the oil package, it is necessary to control three key links to ensure the milling and roughening effect. Start milling the transition section, and the milling depth of the milling machine should be slowly adjusted from zero to the calculated milling depth; Secondly, during the milling process, the milling depth adjustment section, whether increasing or decreasing the milling depth, must be gradually adjusted from the original milling depth to the new milling depth, and sudden changes are strictly prohibited. This requires that the position of the adjustment transition section be calibrated when defining the milling interval; Thirdly, at the end of the milling transition section, the milling machine should also slowly reduce the original milling depth to zero.

銑刨作業時保證縱向邊線的順直，一段銑刨完成后銑刨機直接后退，重新開始向前面銑刨。

During milling operations, ensure that the longitudinal edge line is straight. After completing a section of milling, the milling machine will directly move back and start milling again towards the front.

當一個銑刨段中包括幾個連續銑刨區間時，可以實施連續銑刨，在銑刨中調整銑刨深度，保證路面縱向平順。

When a milling section includes several continuous milling sections, continuous milling can be implemented, and the milling depth can be adjusted during milling to ensure the longitudinal smoothness of the pavement.

對銑刨拉毛面的缺陷必須進行及時處理，如松散部位的與修復，裂縫處及時灌縫等。在每處病害銑刨基坑的起訖位置，會由于銑刨鼓的圓形而形成弧面，在基坑整理時需要人工切割成豎直面，達到基坑四面方正。

The defects on the milling and roughening surface must be dealt with in a timely manner, such as removing and repairing loose parts, and filling cracks in a timely manner. At the starting and ending positions of each diseased milling and planing foundation pit, a curved surface will be formed due to the circular shape of the milling drum. During the foundation pit preparation, it needs to be manually cut into vertical planes to achieve a square shape on all sides of the foundation pit.

對銑刨深度已達到設計但病害仍未的病害，及時與現場監理工程師和業主銜接，確定施工方案和工程數量，以便同步一次將病害銑刨，節省機械二次調轉時間和費用。

For diseases that have reached the designed milling depth but have not yet been eliminated, timely communication with the on-site supervision engineer and the owner should be made to determine the construction plan and quantity of work, so as to synchronously milling and planing the diseases in one go, saving time and cost for mechanical secondary adjustment.

感謝您的閱讀，此文的文章來源：冷再生機租賃更多的內容和問題請點擊：http://m.jsscr.com我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for reading. The source of this article is: Cold Recycling Machine Rental. For more information and questions, please click: http://m.jsscr.com We will continue to work hard to provide you with services. Thank you for your support!