在使用冷再生機的時候，若是發生了攪拌不均勻這一狀況的話，那么就需要引起大家注意了，因為這將會影響到冷再生機的使用效果，所以還是需要及時的采取措施來進行解決，這樣的話才可以有效的解決攪拌不均勻的現象，下面冷再生機出租廠家來講解下，冷再生機攪拌不均勻的解決方法吧。

If the uneven mixing occurs during the use of cold regenerator, we should pay attention to it, because it will affect the use effect of cold regenerator, so we still need to take timely measures to solve it, so that we can effectively solve the uneven mixing phenomenon. Now let the cold regenerator rental manufacturer explain the solution to the uneven mixing of cold regenerator.

一、減少冷再生機各部件的摩擦阻力：

1、 Reduce the friction resistance of various parts of the cold regenerator:

嚴格執行機械技術保養制度，按規定進行潤滑，以降低運行機構的阻力損失，如鼓筒輪箍與滾子表面間的滾動摩擦阻力，滾子的支承軸與軸套之間的摩擦阻力，以及提升料斗的阻力等，從而提高機械效率。

Strictly implement the mechanical technical maintenance system and lubricate as required to reduce the resistance loss of the operating mechanism, such as the rolling friction resistance between the drum tyre and the roller surface, the friction resistance between the roller bearing shaft and the shaft sleeve, and the resistance of the lifting hopper, so as to improve the mechanical efficiency.

二、減少冷再生機無效負荷：

2、 Reduce the invalid load of cold regenerator:

減少機械無效負荷可從加料、攪拌和出料工序采取措施：加料斗卸料完畢應及時放下，以減少振動的能耗，正確掌握攪拌時間，在保證混凝土質量的前提下，適時卸出，從而減少功率消耗，卸料干凈、如果攪拌筒粘料太多，應進行清理、殘料過多不但影響生產率，而且增加功率消耗。

Measures can be taken to reduce the mechanical invalid load from the feeding, mixing and discharging processes: the feeding hopper shall be put down in time after discharging to reduce the energy consumption of vibration, correctly control the mixing time, and discharge in time on the premise of ensuring the concrete quality, so as to reduce the power consumption. The discharge is clean, and if the mixing drum has too much sticking, it should be cleaned. Excessive residue not only affects the productivity, but also increases the power consumption.

三、縮短冷再生機空轉時間：

3、 Reduce idling time of cold regenerator:

除了按操作規程進行起動和停機保養的空轉時間以外，在施工過程中，應盡量縮短機械空轉時間、對冷再生機，如因供料不及時或棍凝土運輸、澆注等原因造成空運轉在1分鐘以上者、應空載停機、節約電能，對于拌和機，則應及時調節油門，使內燃機怠速運行、若空轉時間較長，也應停機、降低油耗。

In addition to the idle time for starting and stopping maintenance according to the operating procedures, during the construction process, the idle time of the machinery should be shortened as much as possible. For the cold regenerator, if the idle time is more than 1 minute due to the untimely supply of materials or the transportation and pouring of stick concrete, the machine should be stopped without load to save electric energy. For the mixer, the accelerator should be adjusted in time to make the internal combustion engine run at idle speed. If the idle time is long, the machine should also be stopped Reduce fuel consumption.

四、其它措施：

4、 Other energy-saving measures:

可參照電動機或內燃機的經濟使用措施，為了能夠保證冷再生機的使用壽命，還需要對其進行保養，冷再生機進料側拌葉長期使用，可能會出現變形或者損害的現象。出現變形的話，只能對拌和機拌葉進行修復或者更換，拌和機出料側拌葉出現變形或者損害的現象，對變形的葉片進行修復或更換。

Refer to the economic use measures of electric motor or internal combustion engine. In order to ensure the service life of cold regeneration, it is also necessary to maintain it. The mixing blade at the feed side of the cold regeneration machine may be deformed or damaged if it is used for a long time. In case of deformation, the mixing blade of the mixer can only be repaired or replaced. If the mixing blade at the discharge side of the mixer is deformed or damaged, the deformed blade can be repaired or replaced.

為了能夠保證冷再生機的使用壽命，還需要對其進行保養，日常的檢查與維護工作必不可少，更多相關內容就來我們網站http://m.jsscr.com咨詢了解！

In order to ensure the service life of cold reinvigoration, it is also necessary to maintain it. Daily inspection and maintenance work is essential. More relevant content is available on our website http://m.jsscr.com Consult and understand!