銑刨機主要用于公路路面養護，在工作時刀頭與路面的基礎是比較多的，所以長期工作下來刀頭的磨損不可避免，需要定期維護，當然這樣的損壞屬于正常因素。在日常使用過程中也有非正常因素造成的損壞，冷再生機租賃廠家今天就來簡單說說這個問題。

The milling machine is mainly used for road surface maintenance. There are many bases between the cutter head and the road surface when it works. Therefore, the wear of the cutter head is inevitable after long-term work, and regular maintenance is required. Of course, such damage is a normal factor. In daily use, there are also damages caused by abnormal factors. Today, the cold regenerator rental manufacturer will briefly talk about this problem.

1、清潔作業造成的損壞

1. Damage caused by cleaning operation

當清理橋底時，由于橋面鋼筋鋪設深度不同，銑床容易對鋼筋進行規劃，對刀盤造成損壞。它甚嚴重地被鋼筋夾住，纏繞在滾筒上。因其它部件卡住或損壞而引起的發動機過載和熄火。

When cleaning the bridge bottom, the milling machine is easy to plan the reinforcement and damage the cutter head due to the different laying depth of the bridge deck reinforcement. It was even seriously clamped by the steel bars and wound on the drum. Engine overload and stalling caused by seizure or damage of other components.

2、城市道路運營損壞

2. Urban road operation damage

城市道路加瀝青時，有些井蓋未經升級，仍埋在瀝青路面下。在路面修補時，由于此類路面瀝青層較厚，很容易刨到井蓋，造成刀盤損壞。

When asphalt is added to urban roads, some well covers are still buried under the asphalt pavement without upgrading. During pavement repair, due to the thick asphalt layer of such pavement, it is easy to plane the well cover, causing damage to the cutterhead.

3、拋板磨損損壞

3. The throwing plate is worn and damaged

拋板不能及時將廢料從銑房內，造成內部廢料不斷地與刀盤和刀架摩擦，增加了刀盤的磨損速度，也影響拋板的工作效率。長時間使用會導致刀頭刀座異常損壞。

The throwing plate can not remove the waste from the milling room in time, which causes the internal waste to constantly rub with the cutter head and the tool holder, increasing the wear speed of the cutter head, and also affecting the working efficiency of the throwing plate. Long time use will cause abnormal damage to the cutter head and cutter seat.

要注意，每次操作前，要檢查皮帶松緊度。新皮帶在運轉4小時后應該重新調整松緊度，須保持適當?shù)钠删o度，才能把發動機的輸出馬力傳送到銑刀鼓上，當太緊的皮帶會容易磨損，同時還會縮短軸承的壽命，如有斷痕、嚴重磨損的皮帶應立即換新的;

It should be noted that the belt tightness should be checked before each operation. The tightness of the new belt should be readjusted after 4 hours of operation. Proper belt tightness must be maintained to transmit the output horsepower of the engine to the milling cutter drum. When the belt is too tight, it is easy to wear and shorten the life of the bearing. If there are broken marks and severe wear, the belt should be replaced immediately;

每次操作前用肉眼檢查機器：所有緊固件是否擰緊?是否有零件明顯磨損或開裂?供油油路是否完好?檢查軸承、檢查各個防護罩是否蓋住等。

Visually check the machine before each operation: Are all fasteners tight? Are there any parts obviously worn or cracked? Is the oil supply circuit in good condition? Check the bearing and whether each protective cover is covered.

以上就是關于銑刨機刀頭損壞的原因分析，希望對您有幫助，當然也要對其進行定期的維護保養，這樣才能更好的延長它的使用壽命，更多事項就來我們網站http://m.jsscr.com咨詢了解吧。

The above is about the cause analysis of the damage of the milling machine tool head. I hope it will be helpful to you. Of course, regular maintenance should also be carried out for it, so as to better extend its service life. Please come to our website for more information http://m.jsscr.com Ask and understand.